Feeds:
Posts
Comments

Posts Tagged ‘Clay Beads’

Welcome to my tutorial on how to make African style beads in polymer clay 🙂

After searching for a stamp to make patterns in my clay beads & being unable to find any in the designs I required I sat down for a coffee & thought ‘why not make my own?’ So it is a little experimental but a lot cheaper & you are welcome to share this project too. The design possibilities are endless – floral, fairy tale, celtic you name it! Also experiment with colours too – blues & purples with silver/pearl paints for example.

What You Will Need – 

  • Polymer clay e.g. Fimo, Sculpey, etc in earth tones plus large piece of scrap clay
  • Plain tile for working & baking
  • Acrylic roller/ Pasta machine
  • Craft knife
  • Ruler
  • Paper & pencil
  • Hand held multi tool (e.g. Dremel) engraving attachments or fine engravers
  • Darning/tapestry needle
  • Acrylic paint in earth tones
  • Small pieces of sponge
  • Matt/gloss polymer clay varnish 

 

What To Do –

Step 1

getclay

 

 

 

Get a reasonable sized piece of scrap clay, preferably in one colour as it makes it easier to see pattern later. Set up you tile & work space ready for some funky beads!

 

 

 

 

 

Step 2

rollclay

 

 

 

Condition (knead) clay until well mixed & workable. Roll out on tile until aprox 3-6 mm depending on how deep you wish your pattern to be. You can remove any air bubbles by pricking them with a pin.

 

 

 

 

 

Step 3

cutclay  

 

 

At this point you can cut your clay to make it all nice & neat – not essential but your more than welcome to be fussy about these things 😛 

 

 

 

 

 

 

Step 4

bakeclay

 

 

 

Bake! – always according to the instructions on the packet & keep area well ventilated too. While your clay is getting toasty warm find books, mags & fire up google images to search for inspiration!

 

 

 

 

 

Step 5

doodle

 

Think of a general theme you wish to work on & get some reference. I wanted to work on some beads for my ‘Out of Africa’ project, with a focus on the rustic, earthy tones & textures I wanted these to look very handmade not perfect & polished (well a bit ‘wonky’ really).

Doodle ’til your hearts content – I find it helps even if I change my mind by the next stage!

 

 

 

Step 6

markclay

 

 

 

Draw the designs you have decided upon on to the cooled, baked clay. I find a soft pencil works better & doesn’t dig into the clay while drawing.

 

 

 

 

 

 

Step 7

engraveclay

 

 

Search high & low for where ever it is that you put the Dremel 😛 once found use the engraving attachment to etch in your detail. You can always do this by hand using fine engraving tools though a Dremel is much quicker. Make sure you etch quite deep as you need your pattern to stand out.

 

 

 

Step 8

rollbeads 

 

Give your stamper a good wash in warm soapy water & dry thoroughly. Make balls out of the ‘best’ clay & roll them up your new pattern stamp! Make your holes using a darning/tapestry needle. 

 

 

 

 

 

 

Step 9  

bakeclay

 

 

 

Bake your newly made beads according to the packets instrutions. Pop kettle on while your waiting… mines a coffee, strong, milk but no sugar ta xx

 

 

 

 

 

 

Step 10

paintbeads

 

 

OOOooo messy time! When your beads have cooled get your acrylic paints ready, I have used a mix of burnt sienna & burnt umber to get the  colour I desired. Very lightly dab your paint onto the bead with one sponge & rub it gently off the raised detail with a clean sponge. Apply a coat of polymer clay varnish to your bead & your done…

 

 

 

Finished bead…

finishedbeads    

 

Here it is!

Thanks for reading & I would love to here your comments/suggestions & to know what you have done with this technique x x x 

Read Full Post »